Hit enter to search or ESC to close
Listening to that groovy music in the room, attaining the aura of the right mood and suddenly you suspect a distortion or static in the sound or speaker. This would be something that potentially ruins any cozy environment, now in order to deal with such problems, we have concluded the common ones—also, the method to troubleshoots them.
Certain problems that a room speaker for turntable can possibly face might be because of not maintaining the speaker or using them for too long might cause these culprits;
Here, we have discussed each of these factors in detail, so that if the speaker faces any of the relevant menaces, one might deal with them.
Not Getting Sound at All
It may occur due to complete or partial system failure. To identify the problem, check if the Av receiver is connected properly, after unplugging the receiver from the power source.
Is the AC Receiver is Connected Properly?
Is the AC Receiver is Connected Properly?
If it is connected properly then there be something wrong with the receiver software, for that check different speaker settings. By this, you will come to know, if the system is totally or partially crashed or surged.
Surround Speakers Not Working Sometimes
While listening to music on speaker, you may come across a lack of sound. Make sure your speaker is connected correctly to the receiver and also by moving to different channels to see if the problem is the same for all the channels.
Front Speaker Doesn’t Work
Lack of sound in your front speaker might be due to:
Troubleshoot these probabilities one by one and you will get to know what part is the menace, after knowing, change the relevant settings.
Height Speaker Doesn’t Work
Wrong setting of A/V receiver and inaccurate placement of the speaker may cause lack of sound in the height speaker. To detect a problem, change the position of the speaker or see if something is recommended by the manufacturer on the documents you got while buying the height speaker.
Static Coming from the Speaker
Static may occur due to the speaker’s connection or damage of wire at some point or mismatched amplifier. To check to connect the speaker to different sources and see if the issue remains persistent.
The Entire System Sounds Off
Due to connection problems, wrong placement of the speaker, receiver arrangement, and a heavy bass load of the speaker may cause damage to one or two speakers or whole system.
An Annoying Hum
It is due to the interference of two or more pieces of the speaker on the electric circuit causing or ground loop. To detect the problem, eliminate the switches one by one.
Universal Remote Doesn’t Work
Universal remote doesn’t work due to mismatching of frequency, low charging of the battery, and the source selected.
Getting No Bass
It depends on the frequency crossover of subwoofers, setting of the receiver and subwoofers, placement of the subwoofers, and its connection with the receiver.
Lag Between Sound and Picture
the reason behind it is that the video takes some time to load but the audio is ready to speak, which causes a lag between sound and picture.
Single Speaker Not Working Properly
Check the impedance of the single speaker by using a multimeter. This is due to the low quality of the speaker wire and faulty receiver.
All Speakers are Working, but Sound a Little Off
In this respect, the receiver’s size setting is very important, as it determines the frequency range of your speaker either small or large. Low-end frequencies are a little low- and high-end frequencies mean high pitch. Under the crossover point of subwoofers, you may bypass the frequencies to solve the problem.
Speakers Create Muffled Sounds (When the Audio is Bass Heavy)
A crossover point (one speaker passes sound to the next speaker) the speaker and the subwoofers produce an equal amount of sound. To resolve the issue set the crossover point a little higher than the lowest rated response of the speaker. Also, small speakers can’t produce deep bass, usually, this problem occurs in large speakers.
One Speaker Sounds Off or Completely Different than Others
It occurs if the speaker is out of phase, to check to see the lead cables of the receiver or amplifier to where they are connected. To resolve the issue clean your speaker and see if it sounds correct and keep your wires in phase.
The phase of subwoofers is similar to the phase of the speaker. See if you have a connectivity issue, solve it, and keep your subwoofers in phase to solve the issue.
Trouble Shooting the Problems
Getting to know the culprit and its root cause solemnly helps in removing them. A faulty speaker can be in the right stature after solving the errors. Here, following some troubleshooting processes:
Changing the Room Speakers
If the speakers are too much worn out, then no matter how much you treat them right, in the long run they will keep showing problems. To resolve this one, getting the best budget speakers for turntable will help elevate the environment with robust sound performance.
Turn the Receiver/Amplifier Off and On
To sort out the technical issue of the complex electronics of receiver or amplifier off and on method is used. Firstly, switch of the receiver from the power button for 10 seconds or more and check if the issue is resolved and if not, then a hard reset should be done by unplugging the power cable and power of the power unit.
Test Using Multiple Sources
By using multiple sound or audio sources we can easily resolve the voice issue of the sound system or see the manufacturer’s advice on the documents provided to you by the manufacturer while buying the speaker.
Check the Speaker’s Connection
Check the speaker’s connection if it is securely plugged in or not. No two wires should touch each other, always tight the cable directly and tightly into the place, twisting the exposed speaker wire to 4 inches.
Above we have discussed the common problems in a room speaker that can be not getting sound, an annoying Hum, Surround speakers do not work, Front speaker doesn’t work, Height speaker doesn’t work, all of the speakers are not working, Getting No Bass and Something static coming from the speaker, etc. with their solutions such as checking the speaker’s connection, Testing the speaker by using multiple sources and Turning the receiver/amplifier Off and then back.
About the author